http://m.yongweiauto.com　　豆?jié){石磨機的使用需要得當，不然就會對設備造成損壞，甚有可能危機到操作人員的生命，那么豆?jié){石磨機的操作規程及檢查事項有什么？

　　The use of soybean milk stone mill needs to be proper, otherwise it will cause damage to the equipment, and even may crisis to the safety of the operator's life, so what are the operating procedures and inspection items of soybean milk stone mill?

　　豆?jié){石磨機的操作：

　　Operation of soybean milk stone mill:

　　開機時流量的調節，喂料活門開啟程度的調節范圍應與粉路的流量平衡相適應，不能過大或過小。

　　Flow adjustment when starting up, the adjustment range of feeding valve opening degree should adapt to the flow balance of powder road, not too large or too small.

　　磨粉機喂料機構的調節，在調節每臺磨粉機的喂料機構時，要使掙個磨輥長度上的流量均勻一致，物料性質一致。

　　The adjustment of the feeding mechanism of the mill, when adjusting the feeding mechanism of each mill, the flow on the length of the mill roll should be uniform and the nature of the material should be consistent.

　　研磨效果的調節，根據物料的工藝性質、出粉要求、控制1皮磨的流量，并調節1皮磨的軌距，使調節后1皮磨的軌距達到規定的研磨程度，1皮磨達不到預定的研磨效果將會直接影響其他磨粉機的研磨效果和系統穩定。

　　The adjustment of grinding effect, according to the process properties of materials, powder requirements, control the flow of 1 skin mill, and adjust 1 skin mill gauge, so that the adjusted 1 skin mill gauge to achieve the specified grinding degree, 1 skin mill can not reach the predetermined grinding effect will directly affect the grinding effect and system stability of other mills.

　　檢查注意事項：

　　Precautions for inspection:

　　生產時要隨時檢查喂料效果，保持喂料裝置動作靈活準確，物料應均勻地分配到掙個磨輥長度上。

　　During production, the feeding effect should be checked at any time to keep the feeding device moving flexibly and accurately, and the material should be evenly distributed to the length of the grinding roller.

　　對磨物料來源不止一處的磨粉機，還應檢查各處的物料質量是否基本一致，是否做到了“同質合并”，發現質量差距較大時，應找出原因，及時排出。

　　For the mill with more than one source of materials, it should also check whether the quality of materials everywhere is basically the same, whether the "homogenous combination" is achieved, and find out the reason for the large quality gap, and discharge it in time.

　　豆?jié){石磨機生產中要注意有無粉狀物料粘在輥面纏成環狀。

　　In the production of soybean milk stone mill, attention should be paid to whether powdery materials stick to the roller surface and wind up into a ring.

　　豆?jié){石磨機生產中要注意磨粉機電動機的運轉情況。

　　In the production of soybean milk stone mill, attention should be paid to the operation of the grinding machine.

　　豆?jié){石磨機生產中豆?jié){石磨機出現堵塞、斷流事故時，應即使將磨輥松閘，以免磨損磨齒，并檢查原因和處理。

　　In the production of soya-milk stone mill, when the soya-milk stone mill is blocked or cut off, the roller should be loosened to avoid wear and grinding teeth, and the cause and treatment should be checked.

　　豆?jié){石磨機的操作規程及檢查事項就講到這里了，其中的內容希望大家能夠遵守，對設備對人都是有好處的。更多內容就來網站m.yongweiauto.com咨詢吧。

　　The operation rules and inspection matters of soybean milk stone mill are here, and the content of which I hope we can comply with, it is good for the equipment and people. For more information, visit m.yongweiauto.com.